3D Bioplotter Research Papers

Displaying all papers by G. Siqueira (5 results)

Mechanical Properties Tailoring of 3D Printed Photoresponsive Nanocellulose Composites

Advanced Functional Materials 2020 Volume 30, Issue 35, Article 2002914

3D printing technologies allow control over the alignment of building blocks in synthetic materials, but compositional changes often require complex multimaterial printing steps. Here, 3D printable materials showing locally tunable mechanical properties are produced in a single printing step of Direct Ink Writing. These new inks consist of a polymer matrix bearing biocompatible photoreactive cinnamate derivatives and up to 30 wt% of anisotropic cellulose nanocrystals. The printed materials are mechanically versatile and can undergo further crosslinking upon illumination. When illuminating the material and controlling the irradiation doses, the Young’s moduli can be adjusted between 15 and 75 MPa. Moreover, spatially…

3D printing of shape-morphing and antibacterial anisotropic nanocellulose hydrogels

Carbohydrate Polymers 2021 Volume 259, Article 117716

We report on a procedure for the preparation, printing and curing of antibacterial poly(N-isopropylacrylamide) nanocellulose-reinforced hydrogels. These composites present a highly anisotropic microstructure which allows to control and modulate the resulting mechanical properties. The incorporation of such nanoparticles enables us to modify both the strength and the humidity-dependent swelling direction of printed parts, offering a fourth-dimensional property to the resulting composite. Antibacterial properties of the hydrogels were obtained by incorporating the functionalized peptide ε-polylysine, modified with the addition of a methacrylate group to ensure UV-immobilization. We highlight the relevance of well-adapted viscoelastic properties of our material for 3D printing by…

Additive manufacturing of silica aerogels

Nature 2020 Volume 584, Pages 387–392

Owing to their ultralow thermal conductivity and open pore structure, silica aerogels are widely used in thermal insulation, catalysis, physics, environmental remediation, optical devices and hypervelocity particle capture. Thermal insulation is by far the largest market for silica aerogels, which are ideal materials when space is limited. One drawback of silica aerogels is their brittleness. Fibre reinforcement and binders can be used to overcome this for large-volume applications in building and industrial insulation, but their poor machinability, combined with the difficulty of precisely casting small objects, limits the miniaturization potential of silica aerogels. Additive manufacturing provides an alternative route to…

Complex‐Shaped Cellulose Composites Made by Wet Densification of 3D Printed Scaffolds

Advanced Functional Materials 2020 Volume 30, Issue 4, Article 1904127

Cellulose is an attractive material resource for the fabrication of sustainable functional products, but its processing into structures with complex architecture and high cellulose content remains challenging. Such limitation has prevented cellulose‐based synthetic materials from reaching the level of structural control and mechanical properties observed in their biological counterparts, such as wood and plant tissues. To address this issue, a simple approach is reported to manufacture complex‐shaped cellulose‐based composites, in which the shaping capabilities of 3D printing technologies are combined with a wet densification process that increases the concentration of cellulose in the final printed material. Densification is achieved by…

Dynamics of Cellulose Nanocrystal Alignment during 3D Printing

ACS Nano 2018 Volume 12, Issue 7, Pages 6926–6937

The alignment of anisotropic particles during ink deposition directly affects the microstructure and properties of materials manufactured by extrusion-based 3D printing. Although particle alignment in diluted suspensions is well described by analytical and numerical models, the dynamics of particle orientation in the highly concentrated inks typically used for printing via direct ink writing (DIW) remains poorly understood. Using cellulose nanocrystals (CNCs) as model building blocks of increasing technological relevance, we study the dynamics of particle alignment under the shear stresses applied to concentrated inks during DIW. With the help of in situ polarization rheology, we find that the time period…